ISSN:2321-6212

All submissions of the EM system will be redirected to Online Manuscript Submission System. Authors are requested to submit articles directly to Online Manuscript Submission System of respective journal.

Infrared Spectra of Aluminum Fluorocarbon Polymer Compositions to Thermal Signature of Jet Engine

Amir Elsaidy*, Mohamed Kassem, Hesham Tantawy, Sherif Elbasuney and Gaber Zaky M

School of Chemical Engineering, Military Technical College, Kobry Elkoba, Cairo, Egypt

*Corresponding Author:
Amir Elsaidy
School of Chemical Engineering
Military Technical College, Egypt
Tel: 61 2 9385 8100
E-mail: amir.alsaidy@mtc.edu.eg

Received Date: 17/09/2018; Accepted Date: 09/10/2018; Published Date: 16/10/2018

DOI: 10.4172/2321-6212.1000232

Visit for more related articles at Research & Reviews: Journal of Material Sciences

Abstract

 Flares are energetic materials, which can yield thermal signature that can to interfere with infrared guided missiles. Flare thermal signature should be similar to aircraft but with higher intensity; this signature depends on exothermal reaction as well as the chemical nature of combustion products. Aluminum is the most common reactive metal fuel in use in energetic systems as it can offer high heat output (32000 J/g) as well as superior chemical stability. In this study, different flare formulations based on aluminum as a fuel, fluorocarbon polymer (Teflon) as an oxidizer, and Viton as a binder (with fuel percentage from 40:70 wt%) were developed by granulation and subsequent pressing. The spectral performance of developed formulations was evaluated to the thermal signature of aircraft jet engine using (FT-MIR 2-6 μm) spectrophotometer. The thermal signature of jet engine was characterized with two characteristic peaks over α (2-3 μm) and β (3-5 μm) band; this signature was correlated to black body emission by the hot nozzle at 690°C. The developed flares offered similar thermal signature but with higher intensity. Aluminum/Teflon/Viton (ATV) flare, with 50 wt% Al, offered an increase in the intensity of α band and β by 6 and 1.5 times respectively. The developed ATV flare offered characteristic intensity ratio Ɵ (Iα/Iβ) (the main spectral parameter) of 0.73; this value was found to be in good accordance with literature. Quantification of infrared emitting species as well as combustion temperature was conducted using the ICT thermodynamic code. ATV flare (50 wt% Al) offered the highest percentage (78.1 wt%) of AlF the main IR emitting species as well as 12.1 wt% of C soot which is an ideal black body emitter. This is manuscript would open the route for the development of flares with tailored spectral performance.

Keywords

Decoy flares, ATV, Infrared, Spectroscopy, Thermal signature

Introduction

Infrared (IR) guided missiles represent the major threat to military aircrafts; they resulted in 90% of aircraft damage [1]. IR seekers can detect IR radiation; subsequently it can identify the aircraft as a potential target [2,3]. Aircraft thermal signature is generated via several components including: the metal skin, jet engine, and exhaust. The aircraft fuselage emits between 8-10 μm, due to sun radiation or air friction. Emission over the range of 3-5 μm is resulted from hot exhaust gases (H2O, CO, CO2). Hot jet engine emits in the range of 2-2.5 μm (Figure 1) [2].

material-sciences-infrared

Figure 1: Main infrared radiation sources of an aircraft.

Heat-seeking missiles search for radiation released from the aircraft over α (2-3 μm) and β (4-5 μm) bands with relative intensity ration [4]. Decoy flare is the main countermeasure technique that can be employed to protect aircraft against thermal detectors [5].

Standard flares consist mainly of Magnesium (fuel), Teflon (oxidizer), and Viton (binder); they are commonly known as MTV flares [2,6]. Nowadays, aluminum is the fuel of interest for different pyrotechnic formulations due to its high heat output (32000 J/g) and high chemical stability [7-10]. While aluminum metal fuel can develop a protective oxide layer offering extended storage time without loss of reactivity (Figure 2); magnesium fuel suffers from lack of chemical stability. Mg is susceptible to acid and humidity with the formation of Mg(OH)2 with loss of reactivity [11].

material-sciences-protective

Figure 2: Aluminium particles with protective oxide layer of Al2O3.

Aluminum can act as high energy density material; it has found wide applications in different energetic systems [12]. Straight way to increase the overall released energy, can be achieved by incorporating reactive metal fuel (i. e. Al) into the energetic system [13-15]. Aluminum can react not only with free oxidizing element (oxygen/fluorine) available from oxidizer; but also it can react inert gasses adding substantial heat output [16].

2Al(s)+3/2 O2 → Al2O3 (s)+1700 KJ/mol (1)

2Al (s)+3CO (g) → Al2O3+3C+1251 kJ/mol (2)

2Al (s)+3H2O (g) → Al2O3 (s)+3H2(g)+866 kJ/mol (3)

2Al (s)+3CO2(g) → Al2O3+3CO+741 kJ/mol (4)

2Al (s)+N2 (g) → 2AlN+346 kJ/mol (5)

These set of reactions can offer substantial heat ouptput. Furthermore, Al can find wide application in thermite reactions. Thermite particles composed of Al/Fe2O3, Sr(NO3)2, were combined with energetic binder to develop the so-called “pyro-organic” flare formulations; this flare demonstrated a promising relative intensity ratio(ɵ) under dynamic conditions [17].

The relative intensity ratio (θ) is defined as the ratio of the average intensity in the α band (2-3 μm) to the average intensity of the β band (3-5 μm) (Eqn. (6)).

ɵ = Iα/Iβ (6)

For IR emitting flares, it is important to offer not only thermal signature similar to aircraft but also the relative intensity ratio should be comparable to aircraft. Consequently the main parameters for effective development of decoy flare include:

• High emissivity values.

• High combustion temperatures.

• θ value lies between 0.5-0.8.

For an aircraft, θ value in the range of 0.7; recent decoy flares offered θ values of 1.3-1.4 [2,4]. This study is dedicated to the effective development of novel decoy flare that can offer high emissivity, high combustion temperature, and with Ɵ value similar to that of the aircraft. Flare with such characteristics could be an effective countermeasure against infrared missiles attacks. The development of decoy flare with controlled radiant intensity requires physical and chemical means to be applied [1,18-28].

Research studies conducted on Aluminum/Teflon/Viton mixtures were limited to burning temperature and burning rate no information about thermal signature has been reported [29,30]. In this study, thermal signature of jet engine (jet cat p200 sx) was measured using (FT-MIR 1-6 μm) spectrophotometer. The characteristic intensity ratio for this engine was calculated. ATV flares with different fuel percentage were prepared and pressed in the desired dimensions. The spectral performance of developed flares was measured and compared to jet engine thermal signature. Quantification of combustion temperature and the main active emitting species (c soot (nearly ideal emitter), AlF (molecular emitter), and Al (heat source)) in the combustion flame was conducted using ICT Thermodynamic Code (Institute of Chemical Technology in Germany, virgin 2008). ATV flare with 50 wt% Al offered higher intensity over α band (2-3 μm) and β band α band (2-3 μm) by 6 and 1.5 times respectively. The main outcome of this study is that this novel flare offered Ɵ value of 0.73.

Experimental Work

Thermal Signature of Jet Engine Nozzle

Thermal signature of jet engine nozzle (jet cat P200 SX turbine with heavy-duty starter) was measured using (FT-MIR 2-6) spectrophotometer (Figure 3).

material-sciences-signature

Figure 3: Schematic for thermal signature measurements of jet engine nozzle.

Decoy Flare Formulation

Chemicals and materials: The main constituents for flares manufacture include oxidizer, metal fuel, and binder. Teflon can act as an oxidizer; Viton A can act as plasticizer and binder. Table 1 tabulates a list of chemicals used in this study.

Table 1: The function and structure of different used chemicals.

Chemicals Function Function Grade Supplier
Teflon oxidizer image n= 20000 fine powder Alpha
Aluminum fuel Al fine powder Alpha
Viton A binder image 1.85 g/cm³ fluorine: 65% Alpha

An efficient study, to develop ATV flares with improved spectral performance was performed. This study includes the following main steps:

● Fuel percentage range (40:70) wt%

● Oxidizer percentage range (25:55) wt%

● Binder percentage 5 wt%

Table 2 summarizes the chemical composition of different investigated ATV formulations.

Table 2: Chemical composition of developed decoy flares.

Formulation Al Teflon Viton A
wt% wt% wt%
F1 40 55 5
F2 45 50 5
F3 50 45 5
F4 55 40 5
F5 60 35 5
F6 65 30 5
F7 70 25 5

Development technology of decoy flares, should emphasize mixing and homogeneity of different ingredients to the molecular level, as well as accepted mechanical properties.

Decoy flares were developed via granulation and subsequent pressing. This approach can ensure good homogeneity and integrity; it includes 5 main stages as follow:

1. Fine powder less than 300 μm with particle size distribution of Al 80 wt% (250-300 μm) and 20 wt% (<250 μm). Teflon white powder with grain size 10 wt%<2 μm, 90 wt%<20 μm.

2. Intimate mixing of oxidizer, fuel, and binder

3. Granulation was performed to retain the homogeneity of the composition. Alternatively, light and dense materials might segregate during transportation, processing, and storage.

4. Filling, by loading 25 g of the composition into metal cylinder of 2.5 cm diameter.

5. The final product was achieved by applying a pressure about 200 atm.

Figure 4 shows the main steps for manufacture of ATV flares.

material-sciences-manufacture

Figure 4: The main manufacture steps of decoy flares.

All investigated compositions were prepared with the same methodology, to avoid any variability, which would affect the performance.

Thermal Signature Measurements

Thermal signature measurement, of developed flares, was conducted using FT-MIR spectrophotometer with spectral range 1-6 μm. The employed setup for spectral measurements includes combustion chamber, optical fibers, spectrophotometer, and data receiving and recording system (Figure 5).

material-sciences-decoy

Figure 5: The main manufacture steps of decoy flares.

The inlet of the optical fiber was fixed at distance of 1.5 m from the tested flare. Thermal signature was recorded in counts/s for each wavelength. After acquiring data, the average intensity of α and β bands was evaluated using MATLABR2014 b software.

Results and Discussion

Thermal Signature of Aircraft Engine

Thermal signature of aircraft engine demonstrated two main characteristic peaks over α band (2-3 μm) and β band (3-5 μm). The jet engine thermal signature was correlated to black body emission by the nozzle at 690°C.

Absorption of the IR emission by air (CO2 and H2O) could attenuate the signal over the region 3-4 μm due to CO2 and H2O IR absorption [31,32]. This jet engine has θ value of approximately 0.3. Figure 6 demonstrates the thermal signature of jet engine nozzle.

material-sciences-nozzle

Figure 6: Imprint spectrum of jet engine nozzle.

Thermal Signature of ATV Flares

Thermal signature measurements demonstrated an increase in the intensity of α and β bands with the increase in Al content. Figure 7 demonstrates the IR spectra of the ATV compositions within the band 1-6 μm as function with Al content.

material-sciences-aluminum

Figure 7: Imprint spectra of ATV flare formulations with different aluminum fuel percentage.

ATV flare with 50 wt% aluminum offered the highest average intensity in the two bands α and β. The average intensity of α and β bands was increased by 6 and 1.5 times, respectively. The relative intensity ratio θ was found to be 0.73. This superior spectral performance can be ascribed to an optimized combustion process, which could maximize the formation of main infrared emitting species (mainly AlF).

It was assumed that aluminum trifloride (AlF3) is formed during the reaction of aluminum with teflon [33,34]. The combustion temperature reaches 1275°C; at this high temperature the formed AlF3 could be vaporized according to eqn. (7) [30]:

2Al (metal)+3/2C2F4 → 2AlF3(g)+3C (s) (7)

At high temperature AlF3 could react with metalic Al forming aluminum monofloride (AlF) (gas) according to eqn. (8) [35,37]:

ALF3(C)+2Al(metal) → 3AlF(g) (8)

AlF is the active emitting species in the flame zone. ATV formulation (50% Al) offered the highest percentage (78 wt%) of gas AlF (main IR emitting species), 0.022 wt% Al (metal fuel), and 12.14 wt% carbon soot. Table 3 demonstrates the quantification of combustion products as well as combustion temperature using ICT thermodynamic code.

Table 3: The Impact of fuel percentage on the formation of active emitting species.


Fuel%
C(s) Al(g) AlF (g) AlF2 (g) AlF3(g) Al4C3(s)
wt% wt% wt% wt% wt%
40% 14.8 0.088 38.4 30.5 14.7 0
45% 13.6 0.065 58.5 19.3 7.7 0
50% 12.1 0.022 78.1 6.33 2.2 1.055
55% 7.7 0.022 71.04 5.4 1.7 13.99
60% 10.01 25.79(l) 49.2 5.8 9 0
65% 8.5 34.14(l) 42.02 14.9 0 0
70% 7.61 48.067 27.506 4.456 12.267 0

AlF is a molecular species that would emit in the infrared region. This active species could be formed in the primary flame zone (1) next to the burning surface (Figure 8).

material-sciences-flarecombustion

Figure 8: Model for ATV flare combustion (a); practical photo-image for ATV flarecombustion (b).

This primary zone is characterized with high combustion temperature and high density of (carbon soot) heated up by primary combustion products (i.e. AlF). This (carbon soot) at high temperature could be nearly ideal emitter (with ε=0.9). Adjacent to the primary reaction zone is a secondary zone (2) (sparks) where Al fuel (small percent in vapor phase) which could be oxidized by air forming Al2O3. The outer zone (3) demonstrates thermally glowing carbonaceous particles that undergo combustion to form CO2. Furthermore, formed CO2 yeild strong peak emission at 2 μm and strong emission bands at 4.3 μm. At this zone (3) complete oxidation of combustion, products could take place.

Thermal Signature of ATV Flare to Jet Engine Nozzle

Comparative investigation between thermal signature of jet engine nozzle and ATV flare with highest spectral performance was developed. The thermal signature of jet engine was characterized with two characteristic peaks over α and β bands. Average intensity ratio (θ) of the jet engine =0.3. The ATV flare offered similar α and β bands but with higher intensity due to the formation of active IR emitting species in the combustion flame. ATV flare with 50 wt% Al offered an increase in the intensity of α and β bands by 6 and 1.5 times respectively. This formulation offered θ value of 0.73. Figure 9 demonstrates the thermal signature of jet engine to ATV flare with 50-wt% Al.

material-sciences-engine

Figure 9: Imprint spectrum of customized Al TV flare to thermal signature of jet engine nozzle.

Effect of Aluminum Content on Α and Β Bands Average Intensity

The variation of average intensity of α and β bands with aluminum content was evaluated using (mat lab software). Figure 10 demonstrate the impact of aluminum content on α and β bands average intensity.

material-sciences-intensity

Figure 10: Average intensity of α and β bands as function of Al content.

The effect of Aluminum content can be categorized into three main regions:

• There was unstable burning in α and β bands with Al content (40: 50 wt%)

• The maximum average intensity was at 50% Al percentage.

• There was a decrease in average intensity with Al content from 50% Al till 70% Al.

Conclusion

Flares should have a fuel rich system to enhance ignitability and combustion stability. The major combustion products are AlF (transient state), AlF3, Al (L), small amount of Al2O3, carbon soot and carbon dioxide. ATV flare with 50 wt% Al offered an increase in the intensity of α and β bands to that of real jet engine nozzle by 6 and 1.5 times respectively. This enhanced spectral performance was ascribed to the high content of AlF (main infrared emitters) in the combustion products. The oxidation of carbon soot to CO2 would yield strong peak emission at 2 μm and strong emission bands at 4.3 μm. This paper would open the route for development of ATV flares with customized spectral performance as an effective countermeasure of IR seekers.

References