ISSN:2321-6212

Yakışıklı erkek tatil için bir beldeye gidiyor burada kendisine türk Porno güzel bir seksi kadın ayarlıyor Onunla beraber otel odasına gidiyorlar Otel odasına rokettube giren kadın ilk önce erkekle sohbet ederek işi yavaş halletmeye çalışıyor sex hikayeleri Kocası fabrikatör olan sarışın Rus hatun şehirden biraz uzak olan bir türk porno kasabaya son derece lüks bir villa yaptırıp yerleşiyor Kocasını işe gönderip istediği erkeği eve atan Rus hatun son olarak fotoğraf çekimi yapmak üzere evine gelen genç adamı bahçede azdırıyor Güzel hatun zengin bir iş adamının porno indir dostu olmayı kabul ediyor Adamın kendisine aldığı yazlık evde kalmaya başlayan hatun bir süre sonra kendi erkek arkadaşlarını bir bir çağırarak onlarla porno izle yapıyor Son olarak çağırdığı arkadaşını kapıda üzerinde beyaz gömleğin açık sikiş düğmelerinden fışkıran dik memeleri ile karşılayıp içeri girer girmez sikiş dudaklarına yapışarak sevişiyor Evin her köşesine yayılan inleme seslerinin eşliğinde yorgun düşerek orgazm oluyor film izle
Reach Us +44-1625-708989

Polymer composite materials and their application in designs of gas turbine engine


4th International Conference on Condensed Matter and Materials Physics

August 16-17, 2018 | London, UK

Sergei V Aliukov, Alexander V Kheruvimov and Alexander V Nikonov

South Ural State University, Russia

ScientificTracks Abstracts: Res. Rev. J Mat. Sci

DOI: 10.4172/2321-6212-C2-017

Abstract

At present, there is a tendency to replace metals with nonmetals, including composite materials. More and more works are devoted to the creation and investigation of the structure and properties of high-temperature nonmetallic materials. Composites, being a heterogeneous anisotropic or quasi-isotropic system, combining the positive properties of components and possessing a complex of new properties not inherent in any of them, allow to substantially improve the basic characteristics of materials. The main requirement applied to the inlet housing of gas turbine engines made of polymer composite materials is the ability to withstand a high operating temperature. Modern polymer composite materials consist of reinforcing fillers and a polymer matrix. Reinforcing fillers can be made of: fiberglass, organic fiber, carbon fiber and are able to withstand the required operating temperature with ease. Thus, the task of selecting polymer composite materials for an input device is reduced to the selection of a polymer matrix connecting the reinforcing filler. This article analyzes the use of polymer composite materials in the details of gas turbine engines of aircrafts, the most promising components of polymer composite materials for manufacturing the input case of a helicopter gas turbine engine have been selected. Samples were made and mechanical tests of polymer composite materials were carried out. Based on the results of the research, the choice of the most promising polymeric composite material was made. The experimental studies carried out on the two most promising materials showed the advantages of a material that has a significantly larger temperature range of operation and has a large margin for modification. It is shown that heat-resistant materials with short-fiber filler can be a worthy replacement for aluminum alloy in the design of the input device. Figure 1: SEM images with different magnifications. Recent Publications 1. Aliukov S (2018) Approximation of electrocardiograms with help of new mathematical methods. Computational Mathematics and Modeling 29(1):59-70. 2. Dubrovskiy A et al. (2017) Basic characteristics of adaptive suspensions of vehicles with new principle of operation, SAE International Journal of Commercial Vehicles. 10(1):193-203.

Biography

Sergei V Aliukov has been doing his scientific research in different areas of his activity, namely, in Engineering, Materials Science, Mathematics, and others. He has published 3 monographs and more than 100 papers. He has developed new methods of approximation of generalized and piece-wise functions and some physical and mathematical models of dynamical processes.

E-mail: alysergey@gmail.com