e-ISSN: 2347-7857 p-ISSN: 2347-7849

All submissions of the EM system will be redirected to Online Manuscript Submission System. Authors are requested to submit articles directly to Online Manuscript Submission System of respective journal.

Formulation and Evaluation of Phytonadione Tablets Using Liquid-Solid Compaction Technique

Anusha Manthani*, M Sunitha Reddy

Department of Pharmaceutical Sciences, Institute of Science and Technology, NTUH, Hyderabad, India

*Corresponding Author:
Anusha Manthani
Department of Pharmaceutical Sciences,
Institute of Science and Technology,
JNTUH, Hyderabad, India
E-mail: manthanianusha46@gmail.com

Received: 19 –Feb-2022, Manuscript No. JPN-22-47657; Editor assigned: 21 –Feb-2022, Pre QC No. JPN-22-47657(PQ); Reviewed: 04- Mar-2022, QC No. JPN-22-47657; Accepted: 09-Mar-2022, Manuscript No. JPN-22-47657(A); Published: 16-Mar-2022. DOI:10.4172/23477857.10.1.002.

Visit for more related articles at Research & Reviews: Journal of Pharmaceutics and Nanotechnology

Abstract

Phytonadione was formulated as a tablet for the treatment of vitamin k deficiency. Even though it is available in other dosage forms like emulsions for injections but it is difficult to handle, maintaining sterility and administration. So present study is to design a simple and novel method for the Formulation of Phytonadione tablets by using liquid-solid compaction technique and develop a dissolution media to meet the bioavailability. Phytonadione tablets were prepared using Colloidal silicon dioxide as adsorbent and carrier to adsorb liquid API. Starch was used as disintegrate to achieve immediate release whereas Acacia used as binder which acts as both binding agent and emulsifying agent. All the formulations prepared were evaluated for various pre and post compression parameters. The selected formulation was subjected to stability studies at 300°C and 400°C. The following procedure for the formulation of tablets was found to be reproducible and stable. There is no loss of assay (99.2%) and final results are within the limits of standard. Therefore phytonadione tablets can provide an attractive alternative formulation to treat vitamin K deficiency.

Keywords

Phytonadione, Liquid-solid compaction, Dissolution, Deficiency

Introduction

Vitamin K is a fat-soluble, yellow color, clear and viscous liquid, which is insoluble in water, slightly soluble in ethanol and soluble in chloroform. It plays an important role in the blood clotting in which deficiency of vitamin K leads to excess bleeding and increases clotting time, which leads to hemorrhage. Vitamin K is responsible for the synthesis of cofactors II, VII, IX and X. This is only fat-soluble vitamin with co-enzyme function. It is absorbed through the lipid micelles through lymphatic system in the small intestine. As it is a fat-soluble vitamin requires bile salts for the absorption. Vitamin K triggers the process of blood coagulation by activating the synthesis of co-factors II, VII, IX and X. It is available mainly in the dosage form of injections which can be administered through Intravenous, Subcutaneous and Intramuscular. But all the time administration is not possible especially self-administration in case of emergency. To overcome these issues converting liquid API into a solid dosage form is preferable [1].

The new liquisolid technique is applied to formulate liquid medications like oily drugs and solutions, emulsions or suspensions into powders suitable for encapsulation or tableting.

Literature survey revealed that the novel technique which is used to convert a liquid into dry, free flowing powder and tablets is known as liquid- solid compaction technique. In this method carrier materials are used to saturate with liquid drug/ drug solution or suspension. After adsorption of the carrier material the surface is blended with fine coating materials. However, an extensive literature search did not reveal any dissolution media for estimation of drug release. Therefore an attempt was made to develop a formulation method and dissolution media as per ICH guidelines for the drug release studies.

Materials and Methods

Materials

Phytonadione (API) from sigma- Aldrich, gum acacia and colloidal silicon dioxide (Aerosil) from S-zaveri supplier, di-calcium phosphate (Di-tab) purchased from Innophos, Lactose (DFE pharma), starch (Signet), Mg stearate (peter greven), and Talc from Imerys.

Methods

Determination of solubility

Solubility of phytonadione was performed in various solvents like water, ethanol, methanol and chloroform [2]. By adding drug to the vehicles and shaking on a shaker for 24 hrs the saturated solutions were prepared under constant vibration. Then these solutions were filtered, diluted and analysed by UV-spectrophotometer at 254 nm.

Formulation of liquid-solid compact

• Weigh all the ingredients according to the quantity per unit.

• Sift the intragranular portion of materials through ASTM #40 mesh.

• Charge the sifted material into the granulator.

• Add the liquid API under continuous mixing with the speed of impeller-95 and chopper 1400.

• Continue the mixing with speed of impeller-105 and chopper-1440 until the lumps are breakdown.

• Blend the above material by using extra granular portion in an octagonal blender which is sifted through ASTM #60 mesh.

• Compress the above blend into tablets by using rotary compression machine.

Preparation of phytonadione tablets

Phytonadione tablets were prepared by taking 5 mg of drug and mixed with aerosil 200 and di-calcium phosphate for 5 min [3]. Then Acacia was added followed by spray dried lactose and sodium starch glycolate for another 5 min. After that glidant and was added and blended for 10 min and then compressed by tablet compression machine.

Evaluation of phytonadione tablets

Drug- excipient compatibility studies: In general while preparing a formulation of tablet, the drug may interact with other excipient as they are in close contact with each other. This interaction sometimes it may leads to instability of a drug. Therefore to know the compatibility between these materials FT-IR spectroscopy was employed. Potassium bromide was mixed with drug and/or other excipient in the ratio of 9:1 then spectra was taken [4]. Then compare the both FT-IR spectra of drug and excipient.

Pre-compression parameters

Bulk density: The bulk density was performed for a granulated blend as drug is a liquid API and also to know the flow properties of a blend. 25 g of blend was placed in a 100 ml graduated measuring cylinder. Initial volume was observed and cylinder was tapped initially 200 times from a distance of 14 ± 2 mm. The tapping was continued for additional 500 times and then next tapping’s for 1250 counts.

Bulk Density=Weight/Volume

TD = weight of the powder/tapped volume

Compressibility index (Carr’s Index)

The compressibility index of the granules was determined by carr’s index:

Carr’s Index (%) = [(TD-BD)×100]TD

Hausner’s ratio

The hausner ratio of the powder was determined by following equation. Hausner’s ratio=TD / BD

Post-compression parameters

The tablets after punching into tablets from every batch were evaluated for post compression parameters like Thickness, weight uniformity test, hardness, friability, drug content, and drug release studies.

Hardness and friability

Hardness is the measure of tablet crushing strength where tablets should withstand the mechanical shocks during manufacturing, packaging and shipping [5].

Friability is determined by Roche friabilator. It consists of plastic chamber which revolves 25 RPM for 4 min. After the tablets are dropped, they are reweighed. And loss of tablet must be 0.5–1% is acceptable.

equation

Weight variation

The average weights of the 20 tablets are calculated which are randomly selected. And the USP test passes only if NMT 2 tablets are outside the %limits (Table 1).

Limit IP/BP USP
10% 80 mg or less 130 mg or less
7.50% More than 80 mg or less than 250 mg 130 mg to 324
5% 250 mg or more More than 324

Table 1. Weight variation.

Content uniformity test

Initially 30 tablets are randomly selected and 10 tablets are assayed individually. The test passes only if 10 tablets contain NLT 85% and more than 115% of labeled drug and 10th tablet may contain NLT 75% and more than 125% of labeled drug content. If test fails remaining 20 tablets are assayed [6].

Disintegration test

This is the test used to determine the time taken for the tablets to breakdown into pieces in GI tract.

Apparatus–It has a mesh aperture of 2 mm (10#),

Cycles–28 to 32 cycles/min,

Temp of water–37oC +/- 2oC. If 1 or 2 tablets fail, repeat for 12 tablets

In -vitro drug release studies

This test is used to measure the extent and rate of solution formation from dosage forms such as tablets, capsules etc. The dissolution of drug is important for its bioavailability and therapeutic effectiveness.

The release rate of phytonadione from liquisolid tablets was studied using USP Dissolution Testing Apparatus. The dissolution test was performed in 1000 ml of pH 1.2 HCL buffer 3% SLS: Methanol (60: 40) at 37°C ± 2°C and 60 rpm. A sample (1 ml) of the solution was withdrawn from the dissolution apparatus at different time intervals and the samples were replaced with fresh dissolution medium [7]. The samples were filtered and diluted to a suitable concentration. And absorbance of these solutions was measured at 254 nm.

Stability studies

Stability studies were carried out for an optimized formulation according to (ICH) guidelines. The formulations were placed in stability chambers for 3 months at 40 ± 2ºC/75 ± 5% RH conditions. All the optimized formulations subjected for stability were analyzed for the friability, hardness, % drug content, and drug in-vitro release studies by the procedure which stated earlier.

Results and Discussion

Solubility studies

The solubility of drug in the water was found to be insoluble as it is a fat-soluble vitamin and slightly soluble in ethanol. Better solubility was found to be in methanol and chloroform (Table 2).

S.NO. Media Solubility
1 Water Insoluble
2 Ethanol 77.8 mg/ml
3 Methanol 84.6 mg/ml
4 Chloroform 81.3 mg/ml

Table 2. Solubility studies.

Phytonadione tablets formulation design

Phytonadione tablets were prepared by taking drug, aerosil and DCP into a granulator and mixed for 5min. Initially wet lumps were observed so the time of the granulation was increased for 5 more minutes and added the drug slowly under continuous mixing (Figure 1). Then Acacia the binder was added to the above granulated blend followed by spray dried lactose (Figure 2) and sodium starch glycolate which acts as super disintegrant. Then mg stearate and talc was added and final blend was compressed into tablets (Figure 3).

pharmaceutics-spectrum

Figure 1: IR spectrum of phytonadione.

pharmaceutics-ssg

Figure 2: IR spectrum of SSG.

pharmaceutics-dcp

Figure 3: IR spectrum of phytonadione, DCP ,SSG, Aerosil and mg stearate.

Study of powder flow properties

Initially the flow of the powder was very poor as it contains wet lumps and no proper mixing (Table 3).

Ingredient F1 F2 F3 F4 F5 F6 F7
Phytonadione 5 5 5 5 5 5 5
DCP 25 25 25 25 25 25 25
Aerosil 2.5 2.5 2.5 2.5 2.5 2.5 2.5
Acacia 13 10 8 6.5 6.5 6.5(initial) 6.5
Spray dried Lactose 63.2 64.9 66.4 76.4 74.4 74.4 74.4
Maize starch 20 20 20 - - - -
SSG - - - 10 12 12 12
Talc 0.65 1.3 1.3 1.3 1.3 1.3 1.3
Mg stearate 0.65 1.3 1.3 1.3 1.3 1.3 1.3

Table 3. Formulation design of phytonadione liquid-solid tablets.

Pre-compression parameters

Hence the bulkdensity, tapped density, hausner’s ratio and carr’s index values are out of the limits. After optimizing all the stages in the formulation and with proper mixing and increased the time of the mixing the flow property values are within the limits of good flow. The good flow was achieved also by increasing the glidant and lubricants (Table 4).

Formulation trail Bulk density (g/ml) Tapped density (g/ml) Carr’s index (%) Hausner’s ratio
F01 0.7461 0.8281 29.05 1.38
F02 0.4211 0.5249 19.77 1.24
F03 0.5328 0.6126 13.144 1.15
F04 0.5187 0.6215 12.54 1.13
F05 0.4925 0.6126 11.6 1.12
F06 0.5211 0.6249 13.77 1.14
F07 0.5342 0.6319 11.33 1.15

Table 4. Pre-compression parameters of phytonadione liquid-solid tablets.

In-vitro drug release study

Dissolution studies were performed to evaluate the drug release profiles from the dosage form. The drug release was so poor initially in the dissolution media of Ph 1.2 HCL 1.5% SLS, then the concentration of the surfactant was increased to 3%. But still the drug release was not found to be satisfactory. Then the dissolution media was changed to ph 1.2 HCL buffer 3% SLS: Methanol (60: 40) [8]. Among the seven formulations f7 showed the better drug release of 89% in 90 min in ph 1.2 HCL buffer 3% SLS: Methanol (60: 40). From the above results it was clear that increase in surfactant increased the dissolution rate of the drug. And also in the formulation 7 the order of the addition of the excipients is also different than the before trials. So both the order of addition and changing the dissolution media showed its impact to get a better drug release profile (Figures 4 and 5) (Table 5) [9].


S. No

TIME
(min)

Dissolution condition

MEDIA TYPE
pH 1.2 HCL buffer (1.5% SLS) pH 1.2 HCL buffer (3% SLS) pH 1.2 HCL buffer 3%
SLS: Methanol (60: 40)
1 0 1000 ml, USP-I II, 60 rpm, 37℃ ± 2℃ 0 0 0
2 10 20.2 ± 3.47 23.1 ± 2.21 35.6 ± 2.38
3 30 23.6 ± 2.38 31.5 ± 2.78 47.2 ± 3.45
4 45 39.7 ± 1.46 42.7 ± 1.53 61.8 ± 0.27
5 60 48.3 ± 2.58 53.4 ± 2.32 72.2 ± 2.49
6 90 56.1 ± 0.48 68.8 ± 1.84 85.6 ± 2.47

Table 5. Comparative release of drug in different media.

pharmaceutics-media

Figure 4: Dissolution profile in different media.

pharmaceutics-drug

Figure 5: In-vitro drug release profile of phytonadione tablets.

Conclusion

In the present study by using the combination of liquid API and excipients a novel formulation was developed known as liquid-solid compacts. Phytonadione tablets were prepared by liquid- solid compaction method because phytonadione is an liquid API. Phytonadione along with other excipients which are selected for the formulation were compatible and were confirmed by drug excipient compatibility studies. Prepared blend was evaluated for precompression parameters like bulk density, tapped density and Hausner’s ratio and then tablets were evaluated for post compression parameters like thickness, hardness, friability, disintegration and dissolution. All the formulations were evaluated and the formulation F7 was found to be the optimized formulation and this batch was loaded for the stability at accelerated stability conditions (40 ± 2℃/75 ± 5% RH) and the formulation passed the evaluations. The results of the evaluations of the formulation proved that the phytonadione was best suited for the treatment of excess bleeding. Hence it was concluded that the formulation had a better drug release profile.

References